Earthquake Sound Stereo Amplifier PA 600 User Manual

Nova  
Power From The Heavens  
PA-600  
Professional Amplifier  
Operation Manual  
& Technical Guide  
POWER  
PROTECT PEAK  
SIGNAL  
SIGNAL  
PEAK PROTECT  
CH2  
CH1  
LEVEL  
LEVEL  
MIN  
MAX  
MIN  
MAX  
MONO  
2
C H A N N E L S  
/
6 0 0 W A T T S P R O F E S S I O N A L B R I D G E A B L E A M P L I F I E R  
VOLTAGE SELECT  
115V  
230V  
SPEAKER OUTPUT  
CH2  
CH1  
LINE LEVEL INPUT  
CH2  
CH1  
+
CH 2  
-
+
CH 1  
-
CH1  
120W/8 Ohm  
200W/4 Ohm  
120W/8 Ohm  
200W/4 Ohm  
CH2  
FUSE  
T3.15A~230V/50Hz  
T6.3A~115V/60Hz  
230VAC,50Hz  
115VAC,60Hz  
750W  
BRIDGED(MONO)  
400W/8 Ohm  
M A N U F A C T U R E D B Y E A R T H Q U A K E S O U N D C O R P O R A T I O N.  
 
DEAR VALUED CUSTOM ER .  
Earthquake Sound Corporation specializes in manufacturing high end Home and Car  
audio products ranging from the smallest driver to the loudest subwoofer system. In its  
dedication to excellence, Earthquake has maintained extensive programs in research and  
development toprovideyou with thehighest qualityaudioproducts.  
channel @ 4 ohms stereo mode or 110 watts per channel @ 8 ohms (stereo mode); 560 watts  
@ 4 ohms, 380 watts @ 8 ohms (bridged mono mode). Several "professional" features, such  
as 1/4" and XLR input jacks with electronically balanced Low or Medium impedance  
operation have been built into the amplifier. Limiting circuitry with LED indicators  
constantly monitors the output level of each channel and provides protection from clipping,  
thus preventing the generation of speaker-damaging square waves. A built-in protection  
circuit protects the amplifier from overloads, short circuits, and overheating. In addition,  
each channel features a Signal LED to assist in hookup and troubleshooting and a Fault  
LED which indicateswhen theinternal protection circuitry isactivated.  
The PA-600 is a ruggedly constructed high quality professional amplifier. The amplifier  
mounts into a standard 19" rack, requiring only two rack spaces (3-1/2 inches, vertically).  
Two automatic variable-speed internal cooling fans use the sides, rear and the front of the  
amplifier - not the top and bottom - for its air intake and exhaust, allowing you to stack  
multiple amplifier closer together in a rack mount situation. Additional rack support holes  
have been provided along the rear of the amplifier for the most secure installation  
possible. (Useoftheseadditional supportsisstronglyrecommended.)  
This owners manual is designed to better acquaint you with the PA-600 pro-  
amplifier. It is imperative that you read this manual in its entirety. EARTHQUAKE  
technicians and staff are looking forward to answer any questions you might have, please  
call (1-800-576-7944).  
The PA-600 produce up to 300 watts of power per channel @ 2 ohms, 200 watts per  
S O U N D LE VE L  
D BA  
D U R ATI O N  
I N H O U R S  
CAUTION: the PA-600 is capable of generating high sound  
pressure levels. You should exercise caution when operating this  
amplifier system. Long term exposures to high levels of sound  
pressure will cause permanent damage to your hearing. Sound  
pressure levels exceeding 85dB can be dangerous with constant  
exposure. Set your audio system to a comfortable loudness level.  
Earthquake Sound Corporation does not assume liability for  
damages resulting from the direct use of the PA-600 , and urges  
userstoplaythePA-600 in moderatelevels.  
90  
92  
95  
8
6
4
3
TH E CH ART (ON TH E SIDE) SH OWS TH E U.S. GOVERNM ENTS  
OCCUPATIONAL SAFETY AND H EALTH ADM INISTRATION (OSH A)  
REGULATIONS WH ICH WERE IN EFFECT AT TH E TIM E OF TH IS  
P UBLICATION FOR P ERM ISSIBLE NOISE EXP OSURE,  
P ER 29CFR1910.95, TABLE G-16.  
97  
2
100  
102  
105  
110  
115  
1 - 1 1/2  
1
1/2  
1/4 or less  
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-3-  
 
PA-600 AM P LIFIER FRONT & REAR PANELS FUNCTIONS/CONNECTION.  
4
5
6
6
5
POWER  
PROTECT PEAK  
SIGNAL  
SIGNAL  
PEAK PROTECT  
CH2  
CH1  
LEVEL  
LEVEL  
MIN  
6 0 0 W A T T S P R O F E S S I O N A L B R I D G E A B L E A M P L I F I E R  
MAX  
MIN  
MAX  
MONO  
2
C H A N N E L S  
/
2
1
3
7
8
9
10  
14  
15  
7
14  
18  
11  
12  
11  
12  
13  
13  
16  
17  
1. POWER SWITCH:  
4. POWER INDICATOR LED:  
ThisLed illuminateswhen AC power isapplied bymeansofthePower Switch (# 1)  
This switch turns the amplifier on in the up position ("I" pressed in ) and off in the down  
position. When AC power is applied to the amplifier, the power indicator led (# 4)  
illuminates.  
5. PROTECT INDICATOR LED'S:  
These LED's illuminate whenever the internal protection relay for the channel is activated.  
The protection relay is activated for a short period upon initial turn-on and at turn-off to  
prevent transient "spikes" from being reproduced through your speakers. A protect condition  
is also indicated if the unit gets too hot, or if DC voltages are present at the output. During  
thermal protection, both channels are shut down. In the event of DC voltage on the output,  
only the affected channel will be disconnected. The circuitry associated with the LED  
indicatorsprovidesvaluableprotection for both theamplifier and your speakers.  
2. LEVEL CONTROL (CH-1) & MONO:  
This rotary potentiometer controls the sensitivity or gain of (CH-1). Set them to the level  
needed for the desired output. When amplifier is set in the bridge mono mode, only this level  
control (CH-1) isactivein thismode.  
3. LEVEL CONTROL CH2:  
This rotary potentiometer controls the sensitivity or gain of CH2. Set them to the level  
needed for the desired output. When amplifier is set in the bridge mono mode, this level  
control isnot active.  
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-4-  
 
PA-600 AM P LIFIER FRONT & REAR PANELS FUNCTIONS/CONNECTION.  
These jacks accept line level signal sources by means of cables fitted with standard ¼” phone  
plugs. Low or medium impedance balanced or unbalanced sources are acceptable for these  
inputs. Balanced inputs are wired as follows: Tip = Signal (+ ), Ring = Signal (-), Sleeve  
= Ground. Unbalanced inputs may be wired: Tip = Signal, Sleeve = Ground, using a  
“mono” plug.  
6. SIGNAL INDICATOR LEDS:  
These LED's illuminate when signal is detected at the amplifier's output terminals,  
providing accurate visual confirmation of signal presence, which is helpful in hookup, and  
troubleshooting. The output signal must be at least 5% of the amplifier's full rated output to  
maketheLED'silluminate.  
NOTE: The input channel circuitry requires a line level signal of 1.1V RMS or greater to  
drivetheamplifier tofull output.  
7. COOLING FAN EXHAUST VENT:  
The PA 600 employs a pair of variable-speed internal cooling fans to draw air through the  
unit and keep it running cool even under extreme operating conditions. The air is drawn in  
through the unit's side and rear intake vents and is forced out through the front panel  
exhaust vent. This method of cooling draws air out from the interior of the rack and provides  
more efficient cooling methods, which bring air in from the front and exhaust it through the  
back. Keep theseventsclear and freefrom obstruction at all timestoinsureproper cooling.  
13. BINDING POST OUTPUT:  
These output connectors offer an excellent method of connecting the amplifier to your  
speakers using cables terminated with spade lugs, banana plugs, or bare wire. When using  
the amplifier in the Mono Mode, you must use either the two red binding posts or the  
BIAMP/MONO (middle) Phone jack (# 13). The Binding Posts are wired in parallel with  
thePhoneJ acks.  
8. STEREO / MONO SWITCH:  
14. SPEAKER OUT J ACKS:  
This switch connects the channels to work together for more power output. In the  
“STEREO” position the amplifier is in the STEREO MODE; with the switch in “MONO”  
MODE the amplifier is in the Bridge MONO MODE. In the Bridge Mono Mode, connect  
input to Channel 1(Channel 2's inputs are disconnected.) Both amp channels are internally  
bridged together to create a single-channel amplifier of increased output power. Use the two  
red BINDING POSTS (labeled ”Mono/Biamp”) or pins 1+ /2+ of the BIAMP/MONO  
(middle) Phonejack.  
These heavy-duty output jacks are to be used to connect the amplifier to your speakers using  
cables terminated with Phone type plugs. These jacks are wired in parallel with the  
BINDING POSTS: channel 1 and 2 Phone J acks are wired with pin# 1(+ ) positive or “in  
phase”, and pin# 1(-) ground or “out of phase" (wired 1+ 1-). The MONO /BIAMP jack has  
channel 1wired to1+ and 2+ , with 1+ "in phase”.  
15. VOLTAGE SELECTOR:  
9. NEW AUTO ON / OFF:  
Selection of AC 115V/60Hz or AC 230V/50Hz voltage source. Before connecting the power  
plug to the wall AC outlet, make sure your local power line AC voltage matches the voltage  
settingofamplifier.  
The new auto sensing circuitry immediately senses signal as it reaches the amplifier, when  
the music stops it will automatically fall asleep. While in sleep mode the PA-600 consumes  
lessenergythan commonlysold ProAmps.  
16. FUSE: Useonlythetypeoffusespecified on theback ofamplifier.  
10. LIMIT SWITCH:  
Switch to “ON” position to activate the limit circuit to prevent the amplifier from clipping.  
Signal indicator LED's will all be illuminated whenever the input signal attempts to  
overdrive the amplifier's output section. Not only does clipping produce harsh sounding  
distortion, it is also capable of damaging speaker components-particularly high frequency  
drivers.  
17. POWER CORD:  
This heavy duty power cord must be connected to a grounded Ac outlet of the proper voltage  
for the amplifier to operate. TO REDUCE THE RISK OF ELECTREC SHOCK, DO  
NOT REMOVE OR BYPASS THE GROUND PRONG OF THE POWER CORD.  
18. RCA INPUT: this is the simplest / most common way to drive an audio signal into the  
PA-600amplifier.  
11. XLR BALANCED INPUT J ACKS:  
These jacks will accept any balanced or unbalanced low or medium impedence line level  
source by means of a three-pin XLR plug. The wiring for the plug is as follows:  
Pin# 1= Ground,  
NEW:  
Ultra sensitive input pre-amp stage circuitry. Some products on the market can produce  
enough voltage to drive an amp but most don't. Earthquake increased sensitivity by giving  
you more output with less input signal. This new circuitry will allow you to drive the amp to  
full stagewith aslittleas60milivolt.  
Pin# 2= Signal (+ ),  
Pin# 3= Signal (-).  
12. ¼” PHONE J ACK INPUTS:  
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-5-  
 
PA-600 AM P LIFIER CONNECTION (STEREO & M ONO)  
The PA-600 can be used in Stereo Mode as  
two separate power amplifiers, each capable  
of driving loads down to 2 ohms. Each  
channel operates independently and has its  
own input connectors, sensitivity level  
controls, signal indicator LEDS, limiter  
circuitry, fault protection circuitry, power  
amp, and speaker outputs.  
2 t o 8 oh m s r a n g e  
2 t o 8 oh m s r a n g e  
In Stereo Mode, the STEREO/MONO  
SWITCHE must be in the "STEREO"  
position. Either the binding posts or the  
Phone jacks may be used to connect the  
amplifier to the speakers. Both inputs must be  
active (plugged) in stereo mode; either XLR  
input, RCA input, or the Phone J ack input  
can be used.  
From audio source  
The two internal power amplifiers may be  
bridged together to form a single, higher-  
powered amp. In the Bridged Mono Mode,  
the amplifier uses channel # 1 INPUT jacks  
and LEVEL CONTROL; channel # 2 inputs  
are disconnected. Channel # 2 power amp  
receives its signal from channel # 1 input  
This signal is connected to channel 2 prior to  
its Limiter, so each channel is independently  
protected. The STEREO/MONO SWITCH  
must be in the MONO position. Because both  
channels are being used (bridged in series),  
the minimum load impedance is 4 ohms.  
From audio source  
The RED binding post terminals (ch  
1= "+ ", ch 2= " + ") or the middle Phone jack  
(ch # 1) must be used to connect the amplifier  
to the speakers.  
From audio source  
4 t o 8 oh m s r a n g e  
NOTE: Use both  
Red Terminals ONLY  
in Mono Mode  
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-6-  
 
PA-600 AM P LIFIER OP ERATION  
The following diagrams are excerpts from the  
system block diagrams and are intended to  
provide a simplified view of the operating modes  
of the amplifier.  
Stereo Mode:  
RCA# 2  
RING  
TIP  
2
BRIDGE MONO SWITCH: This switch connects  
the channels to work together for more power  
output. With the switch in "MONO" Mode the  
amplifier is in the Bridge Mono Mode. In the  
Bridge Mono Mode, connect input to Channel 1  
(Channel 2's inputs are disconnected). Both amp  
channel are internally bridged together to create a  
single-channel amplifier of increased output power.  
CH 2  
INPUTS  
CH 2  
LEVEL  
3
+
STEREO  
STEREO  
CH 2  
AMP  
STEREO  
1
PARALLEL  
MONO  
BRIDGE  
MONO  
BRIDGE  
MONO  
CH 2 OUTPUTS  
1+  
BRIDGE  
MONO  
2-  
RCA# 1  
RING  
1+  
2-  
Use the two red BINDING POSTS (labeled  
"M on o/B i a m p ") or p i n s 1+ /2+ of t h e  
BIAMP/MONO (middle) Phone jack.  
TIP  
2
CH 1  
LEVEL  
CH 1  
AMP  
CH 1  
INPUTS  
CH 1 OUTPUTS  
3
+
1
Bridge Mono Mode:  
RCA# 2  
RING  
TIP  
2
CH 2  
CH 2  
INPUTS  
+
LEVEL  
STEREO  
3
STEREO  
CH 2  
AMP  
STEREO  
PARALLEL  
MONO  
BRIDGE  
MONO  
1
CH 2 OUTPUTS  
BRIDGE  
MONO  
1+  
2-  
BRIDGE  
MONO  
RCA# 1  
RING  
1+  
2-  
TIP  
CH 1  
LEVEL  
CH 1  
AMP  
2
CH 1  
CH 1 OUTPUTS  
INPUTS  
3
+
1
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-7-  
 
PA-600 AM P LIFIER INSTALLATION & M OUNTING  
Th e P A-600 is specifica lly d esign ed to be r a ck m ou n ted , eith er a s a per m a n en t  
fixtu r e or in "m obile" r a ck. As with a n y la r ge, h ea vy object, a pr oper  
a
in sta lla tion cou ld m ea n th e d iffer en ce between su ccess a n d d isa ster . Th e fr on t of  
th e u n it is d esign ed to a tta ch to sta n d a r d r a ck r a ils. Th e fou r ou ter m ost h oles  
cor r espon d to th e scr ew on sta n d a r d r a ck r a ils (2 r a ck spa ces in h eigh t). Use on ly  
10-32 th r ea d ed r a ck scr ews with la r ge h ea d s (su ch a s a tr u ss h ea d s). Th e u se of  
n ylon r a ck m ou n t wa sh er s between th e scr ew h ea d s a n d th e fa cepla te will keep  
th e fa cepla te fr om bein g scr a tch ed . Du e to th e d epth a n d weigh t of th e P A-600 a  
set of r ea r su ppor t h oles h a ve been pr ovid ed . It is h igh ly r ecom m en d ed th a t th e  
in sta ller u se th ese h oles to su ppor t th e r ea r of th e a m plifier . A su ppor t r a il, sh elf,  
or br a cket ca n be a tta ch ed to th e a m plifier a n d th en to th e in sta lla tion  
en closu r e. On e th ou gh t to keep in m in d wh en con sid er in g th e r ela ted h a r d wa r e  
for th is: m or e is better wh en it com es to a secu r e in sta lla tion - a little extr a tim e  
spen t on in sta llin g a h ea vy object m or e th a n offsets th e possible losses th a t  
cou ld be in cu r r ed if th e object wer e to be d a m a ged d u e to in a d equ a te su ppor t.  
Th e d im en sion s below a r e pr ovid ed to a ssist you a n d /or you r in sta lla tion  
en gin eer in m ou n tin g th e a m plifier secu r ely.  
17.06"  
433.3mm  
INDICATES CENTER OF GRAVITY  
15.43"  
392mm  
1.54"  
39.1mm  
19.00"  
482.6mm  
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-8-  
 
PA-600 AM P LIFIER SP ECIFICATIONS  
P OWER OUTP UT  
2 x 120 wa tts RMS @ 8 oh m s 20Hz-20kHz (ster eo m od e)  
2 x 200 wa tts RMS @ 4 oh m s 20Hz-20kHz (ster eo m od e)  
2 x 300 wa tts RMS @ 2 oh m s 1kHz (ster eo m od e)  
380 wa tts RMS @ 8 oh m s 20Hz-20kHz (m on o m od e)  
600 wa tts RMS @ 4 oh m s 1kHz (m on o m od e)  
+0/-0.5d B, 20Hz-20kHz  
FREQUENCY RESP ONSE  
TOTAL HARMONIC DISTORTION  
<0.05%, 20Hz-20kHz  
SLEW RATE  
40 volts / m icr osecon d  
> 89d B r ef 200 wa tts /4 oh m s (20kHz equ iva len t ba n d wid th )  
2 oh m s or gr ea ter in ster eo m od e  
SIGNAL TO NOISE RATIO  
LOAD IMP EDANCE  
4 oh m s or gr ea ter in m on o m od e  
DAMP ING FACTOR  
CONTROLS  
Typica l 300 (1kHz, 8 oh m s)  
Two Fr on t pa n el level settin g kn obs, on e power switch  
XLR, RCA a n d 1/4" ph on e (tip/r in g/sleeve), on e ea ch ch a n n el  
Bin d in g posts ea ch ch a n n el, P h on e ja cks(on e ea ch ch a n n el)  
Mon o Br id ge m od e select, Lim iter "on "/"off"  
Sh or t cir cu it, open cir cu it, RF bu r n ou t, over tem p, spea ker pr otection r ela ys,  
tu r n on /off tr a n sien t pr otection , DC pr otection , lim iter cir cu itr y  
Va r ia ble speed for ced a ir fa n coolin g r ea r /sid e in ta ke, fr on t exh a u st  
110 VAC 60Hz, 750VA  
INP UT CONNECTIONS  
OUTP UT CONNECTIONS  
MODE SWITCHES  
P ROTECTION CIRCUITRY  
COOLING  
P OWER REQUIREMENTS  
100-120 VAC 50/60Hz, 750VA  
220-240 VAC 50/60Hz, 750VA  
SIZE AND WEIGHT  
19" W x 3.49" H x 15.43" D; 29 lbs.  
482.6m m W x 88.8m m H x 392m m D; 13.2 Kg.  
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-9-  
 
5-YEAR LIM ITED WARRANTY  
Earthquake warrants the original purchaser that all Factory Sealed New Audio  
Products be free from defects in material and workmanship, under normal and proper use,  
for a period of five (5) years from the date of purchase (as shown on the original bill of sale  
with serial number affixed/written on it). The five (5) years warranty period is valid only if  
the product is properly installed by an Earthquake authorized party, and the warranty  
registration card is properly filled out and sent to Earthquake Sound Corporation. If the  
product isinstalled bya non-authorized party, a ninety(90) dayswarrantyperiod applies.  
-
Subsequent damagetoother products.  
A warranty claim will not be valid if the warranty registration card is not properly filled &  
returned toEarthquakewith a copyofthesalesinvoice.  
(E) ServiceRequest:  
To receive product/s service, contact Earthquake service department at (510) 732-  
1000 and request an RMA number (Return Material Authorization), items shipped without  
a valid RMA number will be refused. Make sure you provide us with your complete/correct  
shipping address, a valid phone number, and a brief description of the problem you are  
experiencing with the product. In most cases, our technicians might be able to resolve the  
problem over thephone, thuseliminating theneed toship theproduct.  
(A) Five(5) yearslimited warrantyplan coverageguidelines:  
-
First year: Earthquakepaysfor labor, parts, and ground freight (onlyin  
U S  
mainland, not including Alaska and Hawaii) back tocustomer.  
-
-
Second year: Earthquake pays for labor and parts only, customer must pay freight  
both ways.  
Third, fourth & fifth year: Earthquake pays labor only. Customer must pay for  
partsand freight both ways.  
(F) ShippingInstructions:  
Product/s must be packaged in its original protective boxe/s to minimize transport  
damage. Shipper claims regarding items damaged in transit must be presented to carrier.  
Earthquake Sound Corporation reserves the right to refuse product improperly packed.  
Original bill of sale must accompany product returned for service. We encourage you to  
include with the package a written description of the problem. Ship product to: Earthquake  
Sound Corp. 2727 Mc Cone Avenue, Hayward, CA 94545. Ph (510) 732-1000. You are  
responsiblefor thecost ofshippingtheproduct toEarthquakeSound Corporation.  
(B) Warning:  
Products (sent for repair) that are tested by Earthquake technicians and deemed  
to have no problem, will not be covered by the five (5) years limited warranty. Customer will  
be charged a minimum of one (1) hour of labor (ongoing rates) plus shipping charges back to  
customer.  
(G) DisputesResolution:  
(C) Earthquake agrees to repair or replace - at our option - all such defective products/parts  
subject tothefollowing provisions:  
All disputes - between clients and Earthquake Sound Corporation - resulting from  
the five (5) years limited warranty policy must be resolved according to the laws &  
regulationsofthecountyofAlameda -California.  
-
Defectiveproducts/partshavenot been altered or repaired byother than  
a
n
Earthquakefactoryapproved technician.  
-
Products/parts are not subjected to negligence, misuse, improper use, or accident,  
damaged by improper line voltage, used with incompatible products, or have its  
serial number or any part of it altered, defaced or removed, or have been used in  
anywaythat iscontrarytoEarthquake'swritten instructions.  
(D) WarrantyLimitations:  
Earthquake warranty does not cover products that have been modified or abused. Including  
but not limited tothefollowing:  
-
Damagestospeaker cabinet and cabinet finish duetomisuse, abuse, or  
u s e  
ofimproper useofcleaning materials/methods.  
-
-
-
Bent speaker frame, broken speaker connectors, holes in speaker cone, surround &  
dust cap, burnt speaker voicecoil.  
Fading, deterioration of speaker components & finish due to improper exposure to  
elements.  
Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or  
improper useofcleaning material.  
-
-
Burnt tracerson PCB.  
Product/part damaged duetopoor packaging or abusiveshippingconditions.  
S p eci fi ca t i on s & fea t u r es a r e su b ject t o ch a n g e w i t h ou t n ot i ce.  
w w w .ea r t h q u a k esou n d .com  
-10-  
 
WARRANTY REGISTRATION CARD  
Required Information:  
Apply Serial Number H ere  
First name:___________________________________________________________________________  
Last name:___________________________________________________________________________  
Street address:________________________________________________________________________  
____________________________________________________________________________________  
City:_________________________________________State:_______________ Zip:______________  
Phone number: (_______)______________________________________________________________  
Model number:_______________________________________________________________________  
Date of purchase:_____________________________________________________________________  
Purchase price:_______________________________________________________________________  
Serial number: _______________________________________________________________________  
Dealer name:_________________________________________________________________________  
Dealer address:_______________________________________________________________________  
_____________________________________________________________________________________  
City:______________________________________ State:________________ Zip:_________________  
Signature:____________________________________________________ Date:_________________  
Your Comments: ______________________________________________________________________  
_____________________________________________________________________________________  
_____________________________________________________________________________________  
5
YEARS  
LIMITED  
Hawaii)  
WARRANTY  
(Valid In U.S. Mainland Only- Excluding Alaska  
&
 
 

Dynex TV DVD Combo DX LTDVD20 User Manual
EdgeStar Air Conditioner AP10000HW User Manual
EdgeStar Fan EAC211TS User Manual
Essick Air Humidifier E35000 User Manual
Essick Air Humidifier EA1208 User Manual
Festool Router OF 1400 EBQ User Manual
Fisher Price Baby Swing J6295 User Manual
FoodSaver Calculator VAC 1200 User Manual
Gemini Turntable XL DD50 IV E User Manual
Generac Switch 004635 3 User Manual