Earthquake Sound Speaker AWS 502 User Manual

Sound That Will Move You.  
AWS  
All Weather Speakers  
Owner’s Manual  
& Warranty  
Models:  
AWS-502  
AWS-602  
AWS-802  
Sound That Will Move You.  
Earthquake Sound reserves the right to amend details of the specifications without notice.  
Copyright © Earthquake Sound Corporation  
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545  
Phone: 510-732-1000 Fax: 510-732-1095  
 
Description  
Description  
Specifications  
Specifications  
AWS-502  
AWS-602  
AWS-802  
Thank you for purchasing the new AWS indoor / outdoor speakers by  
Earthquake Sound. Combining the infamous Earthquake Sound that will move  
you with the latest and best weather resistance and manufacturing methods,  
theAWS speakers are ideally suited for you with, the highlight feature being the  
outdoor resistance - sun, rain, snow, heat and cold - or marine use. Their  
presence is as equal indoors as well as out bringing life to your background  
music, hi-fi, or home theater. All models in the AWS line are true two-way  
designs with all acoustic parts sealed and gasketed against penetrating  
weather.  
Frequency Response  
(±3dB)  
68-20kHz  
65-20kHz  
55-20kHz  
Recommended  
Amplifier Power  
20-125 Watts  
8ohm  
35-150 Watts  
8ohm  
60-200 Watts  
8ohm  
Nominal Impedance  
Sensitivity (1W@1M)  
Earthquake Sound Corp. has a proven history of successful and brilliant audio  
products spanning over 19 years. Earthquake specifically designed the AWS  
line to minimize damage caused by extreme weather conditions that typically  
other speakers are not capable of defending against. With a durable  
construction and proven materials like; molded PVC cabinets, electro plating,  
UV protection, aluminum grills and brackets, gold-plated speaker connections.  
Drivers constructed with high roll rubber surrounds, longer excursion for better  
bass. Agile brackets make installation easier in most situations and the  
speakers shape allows for simplified corner placement. TheAWS line is the best  
choice in a large market of uncertain products tochoose from.  
90dB  
96dB  
96dB  
5 inch  
(127mm)  
6 inch  
(152.40mm)  
8 inch  
(203.2)  
Woofer  
(Mica cone with butyl surround)  
25mm ASV voice coil 25mm ASV voice coil 25mm ASV voice coil  
One 3/4” (20mm)  
PEI Mylar Dome  
One 3/4” (20mm)  
PEI Silk Dome  
One 1” (25mm)  
PEI Silk Dome  
Tweeter  
9 5/8” (244.475mm) 11 1/2” (292.10mm)  
7 1/8” (180.975mm) 8 1/2” (215.90mm)  
14 7/16”  
Dimensions without bracket  
(HxWxD)  
(366.7125mm)  
10 3/4” (273.05mm)  
5 3/4” (146.05mm) 7 1/8” (180.975mm) 8 1/8” (206.375mm)  
Powder  
Coated  
Aluminum  
Powder  
Coated  
Aluminum  
Powder  
Coated  
Aluminum  
Grill and Bracket  
Enclosure  
High Temp  
Molded PVC  
High Temp  
Molded PVC  
High Temp  
Molded PVC  
4
5
 
Installation  
Installation  
How to Wire the AWS Speakers  
Connecting to an Amplifier or Receiver  
In order to achieve the best quality and stereo imaging from your AWS  
speakers, you must wire the speakers correctly. Wiring can be quickly and  
easily achieved, but be aware and cautious of your work, wiring incorrectly can  
result in poor sound stage and bass reproduction. 18-gauge (or heavier)  
speaker cables are recommended for lengths ranging from 25 feet and up. Prep  
your cable for installation: strip the ends 1/2” (12mm) to expose wire, and tightly  
twist the ends. For installations that are run on or through a building, use the  
correct weather proofed wire that complies with local codes.  
1) Connect the speaker terminals tothe amplifier speaker outputs.  
2) When making all connections, be sure to connect +(positive) to +(positive)  
and - (negative) to-(negative).  
WARNING L  
Prevent electrical shock, by switching off the amplifier or receiver when making  
connections to the speaker. When making all connections, be sure to connect  
the + (positive) on the speaker to the + (positive) on the amplifier, and the -  
(negative) on the speaker tothe -(negative) on the amplifier.  
-(negative)  
+(positive)  
-
+
+ -  
Amplifier / Receiver  
Verify That You Correctly Connected Your Speakers  
Using the gold-plated binding  
posts: you can easily connect  
It is important that your speakers are hooked up with alike polarity or “in-phase”.  
Use this easy test to determine if you have connected your speakers correctly.  
Place speakers face-to-face, as close together as possible. Set your amplifier to  
mono and begin listening to music, reverse the connections on one of the  
speakers. You should hear distinguishable change in sound. The speaker that  
plays louder and deeper is the one that is connected correctly.  
IMPORTANT: Speaker wire is  
usually marked or textured  
banana-plugs, spade-plugs and  
differently to distinguish between  
bare wire. Insert the wire into the  
positive and negative.  
hole tighten securely (do not let  
bare wire hang out side of hole).  
6
7
 
Installation  
Installation  
Volume and Power Handling limitations  
Mounting the AWS speakers  
The listed power recommendations assume you will operate your system in a  
way that will not produce distortion (blow your speakers). Even these speakers  
can be damaged by a modest amplifier if it is not operated properly. If you hear  
distortion (harsh or crackling noise) your’re over powering the speakers and  
should immediately turn the volume down. Prolonged abuse caused by over  
powering the speakers will cause permanent damage that may not be covered  
by the Earthquake limited warranty.  
Before you fasten all items down, you may want to test the placement of your  
speakers to ensure that you are getting the best sound possible. Use the  
supplied bracket to mount the speaker vertically or horizontally on your chosen  
surface. The bracket offers multiple mounting options; key hole sockets and  
standard screw holes the difference is usually based on the surface type(you  
may want toconsult with an installer regarding the proper hard ware touse).  
To mount, remove the bracket from the enclosure. To make wire less noticeable  
you can insert it from the surface through the hole in the bracket and into the  
connections. Mount the bracket in a desired location, and fasten the speaker to  
the bracket. Finally face the speaker in the direction where the sound will most  
needed.  
Speaker Placement  
Speaker location is one of the key factors for better sound quality. Taking your  
time to place your speakers correctly ensures that your speakers will sound best  
in any indoor or outdoor situation. Stereo sound is best heard when the  
speakers are separated by at least 3-6ft. Usually placing speakers by a wall or  
other surface will increase your bass response. Outdoors, placement under the  
eaves of a roof reduces exposure to constant direct sunlight and precipitation,  
which will extend the speaker life. Respect your neighbors; if you know that it will  
affect your neighbors privacy face the speaker toward the intended listening  
area tocontain the amount of distance that the sound will travel.  
Earthquake also placed two 1/4”  
threaded inserts on the back of the  
speaker for alternative mounting  
options. Some additional options  
include floor stands, hanging devices  
etc... These items can usually be  
found at the dealer where you made  
your purchase or any other audio  
outlet.  
If You Feel That the Speaker is Not Working  
First contact the dealer where the speakers were originally purchased, if this is  
not an option, you may contact the Earthquake service department;  
510.732.1000. Products purchased on auction website or from unauthorized  
Earthquake dealers will be charged shipping, labor and parts. Make sure you  
protect your investment and buy from an authorized dealer.  
8
9
 
WWW.EARTHQUAKESOUND.COM  
VALID IN U.S. MAINLAND ONLY  
10  
11  
 

Electro Voice Speaker EVF 1122S 99 FG User Manual
ETI Sound Systems INC Stereo Amplifier AT 212 User Manual
FIC Computer Hardware SMB 950 User Manual
Frymaster Fryer FMPH155 User Manual
Fujitsu Network Card FPCAC14A User Manual
Fujitsu Stereo System RX100 S2 User Manual
Garmin GPS Receiver VIB10 User Manual
GarrettCom Switch 6K32T User Manual
GBC Binding Machine C340 User Manual
Generac Power Systems Portable Generator 005324 1 005325 1 User Manual